The 2710
7th Gen Manual Programmer with Two Sites
$13,495.00
Available on backorder
Performance
The 2710 Manual Concurrent Programming System® is designed for today’s microcontrollers with their long programming times. Used in combination with FX4™ socket modules, the 2710 is one of the lowest cost-per-device solutions for memory and microcontroller devices. This programmer also has the versatility to program FPGAs, PLDs, and many more device types. BPM Microsystems’ concurrent programmers use fault-tolerant architecture, which means multiple programming sites operate independently within a single job session. As a result, throughput, yields, and uptime are optimized to allow a single operator to produce higher volumes of programmed devices.
Features
- Programs microcontrollers, memories, E/EPROMs, flash EPROMs, PLDs, CPLDs, FPGAs, antifuse FPGAs, and more
- Existing support for hundreds of device packages and thousands of socket modules
- Supports all device packages including, but not limited to DIP, SDIP, PLCC, TSOP, SSOP, PCMCIA, SOIC, LCC, QFP, PQFP, PGA, SIMM, CSP, BGA, µBGA, TQFP and TSSOP
- Compatible with manual and automated standard, FX and FX4 socket modules
- Low voltage support down to 1.5V (Vdd)
- Four times the throughput with FX4 socket modules
- FX4 socket modules include three separate LED’s per socket
- Ability to connect multiple 2710 two-site programmers to the same BPWin job session to create a 4-6 site programming station
- A patented solution to guard against passing blank parts—available only from BPM Microsystems
- Uses USB 2.0 communications bus
- Ideal for low to mid-volume production
- BPWin software provides an intuitive, easy to use interface
- JobMaster feature for job setup and process control
- API option for Job Monitor, Job Control and integration with MES
- Daily releases for new algorithm additions and updates
- 1-year hardware warranty
Devices Supported on 7th Gen
2710 Technical Specs
General Specs
2-Site Model
Operating Voltage: 100-240 VAC
Frequency: 50-60 Hz
Current Rating: 8-4 A (Fuse 250V 6A SB)
Dimensions: 21.55” (547mm) x 8.65” (220mm) x 4.68” (119mm)
Weight: 12.2 lbs. (5.5 kg)
Software
Windows Version: Windows 10 Pro 64
File Type: binary, Intel, JEDEC, Motorola, POF, RAM, straight hex, hex-space, Tekhex, Extended Tekhex, ASCII hex, Formatted Binary (.DIO), AFM, OMF, LOF, MER, and others
Device Commands: blank, checksum, compare, options, program, test, verify, erase, read
Features: data editor, revision history, session logging, online help, device and algorithm information
Hardware
Sites: 2 per chassis; multiple chassis may be linked
Calibration: Annual
Diagnostics: Pin continuity test, ROM, CPU, pin drivers, power supply, communications, cables, calibration, timing, ADC, DAC, interconnects
Memory: 512MB per site
User Interface: Pass, Fail, Active, Start LEDs and Start switch on each site; PC display shows systems status at a glance; auto-start mode automatically begins programming when a device is inserted
PC System Requirements: Windows 10, Windows 7
Standard Accessories Included
- Software on CD-ROM
- User manual on CD-ROM
- Power cable
- Data cable
- 1-year hardware warranty and software support
PIN Drivers
Analog Slew rate: 0.3 to 25V/µs
Vpp Range: 0-25V
Ipp Range: 0-70mA continuous, 250mA peak
Vcc Range: 0-12V
Icc Range: 0-1A
Very low voltage: to 1.5V (Vdd)
Rise Time: 4ns
Overshoot: none
Clocks: continuously variable 1 MHz to 30 MHz
Protection: overcurrent shutdown, power failure shutdown
Independence: pin drivers and waveform generators are fully independent and concurrent on each site
Features
- File Loading: automatic file type identification; no download time because the programmer is PC controlled; supports Intel, JEDEC, Motorola S-record, POF, straight hex, hex-space, Tekhex, and other file formats
- Device Selection: intelligent device selector allows you to type as little or as much of the part number as you like then choose from a list of devices matching your description
- Devices Supported: including, but not limited to, Antifuse, Low Voltage, PROM, EPROM, EEPROM, Flash EEPROM, Microcontrollers, SPLD, CPLD, FPGA
- Continuity Test: each pin, including Vcc, ground, and signal pins, may be tested before every programming operation
- Protection: overcurrent shutdown; power failure shutdown; ESD protection, reverse insertion, banana jack for ESD wrist straps
- Options: available Socket Modules including, but not limited to, Universal PLCC, standard PLCC, PGA, CSP, BGA, µBGA, SOIC, QFP, TSOP, LCC, SDIP, PCMCIA,SIMM—JobMaster™ software, and Advanced Feature Software
- Programming Yield: assured by independent universal pin drivers on each socket, a short distance from pin drivers to device, and accuracy of waveforms
- Algorithms: all algorithms are manufacturer approved or certified (if required)—BPM Microsystems has an excellent record of being first to provide certified algorithms for new devices
- Algorithm Updates: access to algorithm changes and updates are available during the warranty period and via support renewal thereafter
BPM's 7th Gen Programmer users include:









