+1 (713) 263-3776 | Sales Toll-Free: (855) SELL BPM | Service: (888) 490-0241

The 2710–

7th Gen Manual Programmer with Two Sites


Do you have any

Performance 

The 2710 Manual Concurrent Programming System® is designed for today’s microcontrollers with their long programming times. Used in combination with FX4™ socket modules, the 2710 is one of the lowest cost-per-device solutions for memory and microcontroller devices. This programmer also has the versatility to program FPGAs, PLDs, and many more device types. BPM Microsystems’ concurrent programmers use fault-tolerant architecture, which means multiple programming sites operate independently within a single job session. As a result, throughput, yields, and uptime are optimized to allow a single operator to produce higher volumes of programmed devices.

 

Features

  • Programs microcontrollers, memories, E/EPROMs, flash EPROMs, PLDs, CPLDs, FPGAs, antifuse FPGAs, and more  

  • Existing support for hundreds of device packages and thousands of socket modules

  • Supports all device packages including, but not limited to DIP, SDIP, PLCC, TSOP, SSOP, PCMCIA, SOIC, LCC, QFP, PQFP, PGA, SIMM, CSP, BGA, µBGA, TQFP and TSSOP

  • Compatible with manual and automated standard, FX and FX4 socket modules

  • Low voltage support down to 1.5V (Vdd)

  • Available in a two-site model

  • Four times the throughput with FX4 socket modules

  • FX4 socket modules include three separate LED’s per socket

  • Ability to connect multiple 2710 two-site programmers to the same BPWin job session to create a 4-6 site programming station

  • A patented solution to guard against passing blank parts—available only from BPM Microsystems

  • Uses USB 2.0 communications bus

  • Ideal for low to mid-volume production

  • BPWin software provides intuitive, easy to use interface

  • JobMaster feature for job setup and process control

  • API option for Job Monitor, Job Control and integration with MES

  • Daily releases for new algorithm additions and updates

  • 1-year hardware warranty

2710 Technical Specs

General Specs

2-Site Model
Operating Voltage: 100-240 VAC
Frequency: 50-60 Hz
Current Rating: 8-4 A (Fuse 250V 6A SB)
Dimensions and Mass: 21.55” (547mm) x 8.65” (220mm) x 4.68” (119mm), 12.2 lbs. (5.5 kg)

Software

Required: BPWin
File Type: binary, Intel, JEDEC, Motorola, POF, RAM, straight hex, hex-space, Tekhex, Extended Tekhex, ASCII hex, Formatted Binary (.DIO), AFM, OMF, LOF, MER, and others Device Commands: blank, checksum, compare, options, program, test, verify
Features: data editor, revision history, session logging, on-line help, device and algorithm information

Hardware

Architecture: Concurrent Programming System
Sites: 2 per chassis; multiple chassis may be linked
Calibration: annual; may be verified on site with optional socket module
Diagnostics: pin continuity test, ROM, CPU, pin drivers, power supply, communications, cables, calibration, timing, ADC, DAC, interconnects
Memory: 512MB per site
User Interface: Pass, Fail, Active, Start LEDs and Start switch on each site; PC display shows systems status at a glance; auto-start mode automatically begins programming when a device is inserted
PC System Requirements: Windows XP, Windows 7

Standard Accessories Included
  • Software on CD-ROM
  • User manual on CD-ROM
  • Power cable
  • Data cable
  • 1-year hardware warranty and software support
PIN Drivers

Quantity: 240-pins standard
Analog Slew rate: 0.3 to 25V/µs
Vpp Range: 0-25V
Ipp Range: 0-70mA continuous, 250mA peak
Vcc Range: 0-12V
Icc Range: 0-1A
Very low voltage: to 1.5V (Vdd)
Rise Time: 4ns
Overshoot: none
Clocks: continuously variable 1 MHz to 30 MHz
Protection: overcurrent shutdown, power failure shutdown
Independence: pin drivers and waveform generators are fully independent and concurrent on each site

Features
  • File Loading: automatic file type identification; no download time because the programmer is PC controlled; supports Intel, JEDEC, Motorola S-record, POF, straight hex, hex-space, Tekhex, and other file formats
  • Device Selection: intelligent device selector allows you to type as little or as much of the part number as you like then choose from a list of devices matching your description
  • Devices Supported: including, but not limited to, Antifuse, Low Voltage, PROM, EPROM, EEPROM, Flash EEPROM, Microcontrollers, SPLD, CPLD, FPGA
  • Continuity Test: each pin, including Vcc, ground, and signal pins, may be tested before every programming operation
  • Protection: overcurrent shutdown; power failure shutdown; ESD protection, reverse insertion, banana jack for ESD wrist straps
  • Options: available Socket Modules including, but not limited to, Universal PLCC, standard PLCC, PGA, CSP, BGA, µBGA, SOIC, QFP, TSOP, LCC, SDIP, PCMCIA,SIMM—JobMaster™ software, and Advanced Feature Software
  • Programming Yield: assured by independent universal pin drivers on each socket, a short distance from pin drivers to device, and accuracy of waveforms
  • Algorithms: all algorithms are manufacturer approved or certified (if required)—BPM Microsystems has an excellent record of being first to provide certified algorithms for new devices
  • Algorithm Updates: access to algorithm changes and updates are available during the warranty period and via support renewal thereafter

Complete Ecosystem

BPM Microsystems has ownership of all designs, manufacturing, and support for all programming sites, robotics, vision systems, and software, so we can provide unmatched support and responsiveness

  • Reduce your time to market by doing New Product Introduction/First Article through Automated Production with the same hardware, algorithms, and software
  • 2900 and 2900L for Manual Production and Fast First Articles, 3910, 4900 & 4910 for Automated Productiononly BPM can deliver

Intrigued?

Learn How BPM Microsystem's Manual Programming Systems Deliver ROI

Share This